What is power down mode in microcontroller?
Table of Contents
- 1 What is power down mode in microcontroller?
- 2 Does microcontroller have power saving mode?
- 3 How can you put the 8051 in idle mode?
- 4 What is DJNZ instruction?
- 5 What is the difference between microprocessor and microcontroller?
- 6 In which register idle mode and power down mode are used?
- 7 Which of the following is not an addressing mode of 8051?
- 8 What is difference between Lcall and Acall?
- 9 What is the function of Port d in ATmega16?
- 10 What is the throughput of AVR ATmega16?
What is power down mode in microcontroller?
In Power Down mode, the oscillator clock provided to the system is OFF i.e. CPU and peripherals clock remains inactive in this mode. In Idle Mode, only the clock provided to the CPU gets deactivated, whereas the peripherals clock will remain active in this mode.
Does microcontroller have power saving mode?
In this mode the clock is cut from the processor only, other parts of the microcontroller such as timers…. . In this mode 80\% of power is saved. The 20\% power is used to get the microcontroller from idle mode to normal mode….Power Saving Mode in 8051.
| PD | IDL | Status |
|---|---|---|
| 1 | 0 | Power down mode |
| 1 | 1 | Power down mode |
Which two bit of Pcon register are use for selecting power saving option?
The two power saving modes are entered by setting two bits IDL and PD in the special function register (PCON) respectively.
How can you put the 8051 in idle mode?
Idle Mode: 8051 can be put in idle mode by making bit 0 of PCON as 1. Input clock to CPU is stopped and CPU stops working.
What is DJNZ instruction?
The DJNZ instruction decrements the byte indicated by the first operand and, if the resulting value is not zero, branches to the address specified in the second operand.
What is sleep mode in microcontroller?
The term “sleep mode” (sometimes called “power down mode”) refers to a condition in which an embedded system enters a low-power mode. Typically, the microcontroller (MCU) ceases to perform any computations, although it will retain any current data, and peripheral functions will stop working.
What is the difference between microprocessor and microcontroller?
KEY DIFFERENCES Microprocessor consists of only a Central Processing Unit, whereas Micro Controller contains a CPU, Memory, I/O all integrated into one chip. Microprocessor uses an external bus to interface to RAM, ROM, and other peripherals, on the other hand, Microcontroller uses an internal controlling bus.
In which register idle mode and power down mode are used?
The PCON register in the SFR space selects the power-saving mode in 8051. To select IDLE mode, the 0th bit in the PCON register (IDL) is set t0 1, and for power-down mode, bit 1 (PD) is set to 1.
What is Pcon register for?
The PCON or Power Control register, as the name suggests is used to control the 8051 Microcontroller’s Power Modes and is located at 87H of the SFR Memory Space. Using two bits in the PCON Register, the microcontroller can be set to Idle Mode and Power Down Mode.
Which of the following is not an addressing mode of 8051?
Discussion Forum
| Que. | Which of the following is not an addressing mode of 8051? |
|---|---|
| b. | register specific instructions |
| c. | indexed addressing |
| d. | none of the above |
| Answer:none of the above |
What is difference between Lcall and Acall?
ACALL (Absolute Call) The difference between the ACALL and LCALL is that the target address for LCALL can be anywhere within the 64K-bytes address space of the 8051, while the target address of CALL is within a 2K-byte range.
What is an ATMega16 microcontroller?
The ATmega16 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega16 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.
What is the function of Port d in ATmega16?
Port D (PD7-PD0) Port D serves the functions of various special features of the ATmega16 like interrupts input, timer/counter output and UART. In addition to this Port D is used as input/output 8-bit bi-directional port having internal pull-up resistors.
What is the throughput of AVR ATmega16?
The throughput of AVR ATmega16 is about 1 MIPS per MHz using a single clock per instruction allowing the system designer to optimize power consumption versus processing speed. The AVR has 32 general purpose working registers and a rich instruction set.
What are the comparator pins in ATmega16?
Analog comparator pins in ATMega16 are listed below: Capture/Compare/PWM: PWM becomes a basic function for most of the devices to control their voltages. In ATMega16 there are four PWM pins that use Prescaler to generate the desired output signal. Those pins are: