How do you control MLSS?

MLSS concentration in ASP is controlled by Return Sludge and Sludge Wasting. MLSS concentration in ASP is controlled by Return Sludge and Sludge Wasting. MLSS concentration in ASP is controlled by Return Sludge and Sludge Wasting.

How do I reduce pin floc?

Pin floc leads to a more turbid effluent. It is most commonly the result of exceedingly high sludge age. Reducing sludge age often minimizes the occurrences of pin floc. Algae growth within secondary clarifiers is common for uncovered secondary clarifiers.

What happens if MLSS is high?

If the MLSS concentration is above the desired concentration, the wasting of the excess solids will have to be started or increased. If the MLSS concentration is below the desired concentration level, wasting should be decreased or stopped.

How much MLSS maintain in aeration tank?

solids (MLSS) concentration is maintained in the aeration tank of the order of 1500 to 3000 mg/L and mean cell residence time of 5 to 15 days is maintained. The hydraulic retention time (HRT) of 4 to 8 h is required for sewage treatment.

How do you reduce sludge age?

The easiest and most practical way to control sludge age is with hydraulic control by wasting a defined proportion of the reactor volume daily. In AS plants with reactor concentration control, nitrification fails first.

How do you increase MLSS activated sludge?

You can reach an effect similar to having af MLSS of 12 g/L by converting from activated sludge to suspended biofilm system, MBBR. The biofilm is retained in the aeration tank and thus one can achieve higher biomass density. MLSS can be increased by adding part of cow dung slurry.

How can you improve settling in activated sludge?

Excess organic load can be remedied by reducing the waste-activated sludge rate by an amount less than 10 percent per day, to return to proper loading parameters and increase the returned activated sludge rates. About a 30 percent level of settled solids in the clarifier should be established and maintained.

What is floc in activated sludge?

Activated sludge flocs are a flocculated mass of microorganisms, extracellular polymeric substances (EPS) and adsorbed organic and inorganic material. The results indicate that the EPS, both in terms of quantity and quality, are very important for the floc properties of the activated sludge.

How can I improve my MLSS?

The biofilm is retained in the aeration tank and thus one can achieve higher biomass density. MLSS can be increased by adding part of cow dung slurry. Macro nutrients ,Micronutrients which supports the microbial growth may be added.

How do you analyze MLSS?

2. Determination of MLSS

1. Set the temperature of the muffle at 105°C;
2. Weight the blank filter and take note (Mo) [mg];
3. Filter 25 ml of sample and take note of the volume (V) used [ml];
4. Take the filter (after filtration) and put it in the muffle at 105°C for 2h;
5. Let the dried filter for 15 min at room temperature;

How can I reduce sludge?

The new wastewater treatment processes including SANI®, high-rate activated sludge coupled autotrophic nitrogen removal and anaerobic membrane bioreactor coupled autotrophic nitrogen removal also have a great potential to reduce sludge production.

How do I control bulk sludge?

Control of low F/M bulking is by reducing the aeration basin MLSS concentration and increasing the F/M (manipulating the “M” component). Lowering the MLSS concentration may not be suitable for many plants as this may cause the loss of nitrification and increase waste sludge production.

What is the role of MLSS in wastewater treatment?

These solids usually consist mostly of the microorganisms and non-biodegradable matter inside. In the wastewater treatment process, the MLSS helps in ensuring that there is a sufficient quantity of biomass available to consume the quantity of an organic pollutant that is applied.

What is the normal range of MLSS and SVI in wastewater treatment?

Desirable range: MLSS around 3,000 and mg/l and SVI = 100 to 200 ml/g. This would produce a clear and good quality effluent (sludge forms a uniform blanket and capture more particles before settling). SVI = 80 ml/g or less, (rapid settling characteristics). Typically in extended aeration conditions.

How to control MLSS concentration in ASP?

MLSS concentration in ASP is controlled by Return Sludge and Sludge Wasting. MLSS concentration in ASP is controlled by Return Sludge and Sludge Wasting. MLSS concentration in ASP is controlled by Return Sludge and Sludge Wasting. I agree with Pravin. The process is prone to bulking of solids and the treatment system can become overloaded.

What is the concentration of MLSS in activated sludge?

The process may not remove sufficient organic matter from the wastewater. The sludge age may be too low to enable nitrification. The typical control band for the concentration of MLSS in wastewater is 2,000 to 4,000 mg/L for conventional activated sludge, or up to 15,000 mg/l for membrane bioreactors.