How does a foam cannon work?

A foam cannon is a piece of car washing equipment that mixes the perfect amount of car wash soap, water, and air to generate thick suds, then shoot them all over your car using the power of a pressure washer. We always use warm water because it helps the aerate mixture better.

How does a sprayer foamer work?

Starts here2:13Griot’s Garage: Foaming Sprayer – YouTubeYouTubeStart of suggested clipEnd of suggested clip46 second suggested clipAnd caps elating and pulling dirt away from the surface of your paint as it slowly drips off the carMoreAnd caps elating and pulling dirt away from the surface of your paint as it slowly drips off the car before you even have to touch it additionally foam is slick. So you get more lubrication.

Why is my foam cannon so watery?

Improper suction will result in watery foam. High Sudsing Car Soap: Use a quality high sudsing car soap in your foam cannon. Mix 6-8 oz of soap with warm water and fill in the foam cannon.

Can you leave soap in a foam cannon?

Simply rinse your car from top to bottom with your pressure washer, then, proceed to foaming your car. Putting your foam cannon away full of water or full of soap creates calcium deposits which prevent the cannon from shooting the maximum amount of foam.

How many gpm does a foam cannon need?

Most foam lances require a minimum of ~2 gallons per minute (GPM), but the more basic (and affordable) electric pressure washers are generally around 1.2-1.6 GPM, well below the 2 GPM minimum.

Do you hand wash after foam cannon?

Starts here2:36Is Your Car Clean after Just a Foam Cannon Bath? – YouTubeYouTube

What is the difference between foam gun and foam cannon?

Whereas a Foam Cannon will lay down a thick shaving-cream-like layer of white foam over the entire surface, the Foam Gun with a water hose simply does not have enough water pressure to create such a thick foam, but it will still cover the surface in thick suds to help loosen and lift dirt more easily.

How do you make foam cannon thicker?

Starts here7:30How to get MORE FOAM from your Foam CannonYouTube

Why is my foam cannon not thick?

Starts here5:575 reasons your foam cannon doesnt make thick foam – YouTubeYouTube

Do you still have to scrub with foam cannon?

It’s the soap that really does all the work to remove dirt –no scrubbing required. Since a foam cannon applies much more soap than a wash mitt ever could (even those that hold a lot of suds), you really don’t have to use any pressure at all when using a mitt.

Does foam cannon work with 1.2 gpm?

It works with pressure washers with 1.2GPM and over 1,000 PSI. This cannon is easy to operate, doesn’t use a lot of soap, and shoots out an amazing stream of soap.

Is 1.1 gpm good for foam cannon?

Most foam lances require a minimum of ~2 gallons per minute (GPM), but the more basic (and affordable) electric pressure washers are generally around 1.2-1.6 GPM, well below the 2 GPM minimum. …

How do you dilute soap to make foam cannons?

Dilute the Soap With Warm Water Most foam cannons use some advanced techniques to get the right mixture of soap, water, and air to shoot thick foam. In the dilution process, it’s important that you use warm water to ensure proper aeration of the soap and water mixture. This will result in shooting thick foam.

How do you use a chemical guys foam cannon?

Here’s how it works: Mix 1 – 3oz of your favorite Chemical Guys soap and water into the canister of the foam cannon. We always use warm water because it helps the aerate mixture better. Reattach the canister to the head of the foam cannon.

What is a foam cannon?

A foam cannon is a piece of car washing equipment that mixes the perfect amount of car wash soap, water, and air to generate thick suds, then shoot them all over your car using the power of a pressure washer. Pressure washers are awesome.

How does a foam sprayer work?

Answer Wiki. The foam dilutes with water and it pushes through the small hole as water does. It then is pushed up through the sprayer heads and the fan pushes air to push the water/ surfactant mixture through the mesh to make foam.