What is the code for fall protection in construction?

Workers must be protected by guardrail systems, safety net systems, or personal fall arrest systems, even if they are not engaged in leading edge work, if they are on a walking or working surface that is 6 feet or more above a level where leading edges are under construction. 29 CFR 1926.501(b)(2)(ii).

What is the trigger height for fall protection as defined by OSHA construction standards?

ANSWER: Four feet is the fall protection trigger height in General Industry.

Where is fall protection required 100 to 300 personnel?

OSHA requires that fall protection be provided at elevations of 4 feet in general industry workplaces, 5 feet in shipyards, 6 feet in the construction industry, and 8 feet in longshoring operations.

How high can you work without fall protection?

General Industry requires fall protection for any worker over 4′. 1910.28(b)(1)(i) Construction requires fall protection for any worker over 6′.

What OSHA standard addresses fall protection training requirements?

1926.503 – Training requirements.

• Part Number: 1926.
• Part Number Title: Safety and Health Regulations for Construction.
• Subpart: 1926 Subpart M.
• Subpart Title: Fall Protection.
• Standard Number: 1926.503.
• Title: Training requirements.
• GPO Source:

What are the 4 types of fall protection?

All active fall protection for the construction industry falls into four basic categories: fall arrest, positioning, suspension, and retrieval. OSHA provides standards for each category of fall protection.

Which is the best example of a fall prevention system?

Physical barriers like guardrails around unprotected edges and covers over holes are examples of passive fall protection. Passive protection is generally considered to provide a higher level of safety since the opportunity for error is less than using personal protective equipment (PPE).

What are the ways an employer can protect workers from falls OSHA?

There are a number of ways employers can protect workers from falls, including through the use of conventional means such as guardrail systems, safety net systems and personal fall protection systems, the adoption of safe work practices, and the provision of appropriate training.

What is the OSHA standards for construction and general industry known as?

OSHA’s 1910 General Industry and 1926 Construction Standards They’re what’s commonly known as horizontal standards.

What size hole requires a cover?

Every floor hole into which persons cannot accidentally walk (on account of fixed machinery, equipment, or walls) shall be protected by a cover that leaves no openings more than one (1) inch wide. The cover shall be securely held in place to prevent tools or materials from falling through.

What is the difference between fall prevention and fall protection?

Fall prevention is anything that eliminates a hazard altogether. Active fall protection is anything that requires active participation from the worker, i.e. using a fall restraint or fall arrest system. …

What are 3 types of fall protection devices?

Besides fall arrest, there are three more types of fall protection equipment:

• Positioning – These systems hold workers in place while leaving their hands free, to allow them to work.
• Suspension – These systems lower and support workers while leaving their hands free for the activities they need to perform.

What is the OSHA requirement for fall protection?

For general industry, OSHA requires fall protection beginning at a height of four feet. In construction, fall protection is required above six feet. Protection must also be provided any time an employee must work above hazardous equipment or machinery, regardless of the distance.

What are OSHA regulations?

OSHA Regulations. Definition – What does OSHA Regulations mean? The Occupational Health and Safety Administration (OSHA) regulations are the American national standards developed to ensure workplace health and safety for all employees. OSHA’s primary rule is that employers are obligated to provide a safe workplace environment.

What is the subpart fall protection of OSHA?

The intent of OSHA’s Walking-Working Surfaces standard, 29 CFR Part 1910, Subpart D, is to increase the protection of general industry employees and employers from hazards associated with walking-working surfaces . Requires that employers provide protection for each employee exposed to fall and falling object hazards.

What is OSHA’s role in construction safety standards?

OSHA is a business regulator, and it’s their mandate to set standards for your job site and ensure that workers have the right equipment and training to work safely and effectively on any construction project.